|
The
Universal T-Board (Two Button, Closed Bolt)
Installation of the Universal T-Board
See Install Manual.
Functionality
The Universal T_Board function much like a stock board, however, the setting and
LED functions are different. To turn on the marker, (Instant On - off) tap and release the power
button on the membrane pad, (Instant On - on) the marker will turn on as soon as power is applied.
The marker is now ON and in fire mode. The color of the LED will
denote the firing mode that the marker is in (see below). To put the marker in
Safety, tap the power button while Live. The LED will flicker
green quickly. To return to firing mode, tap the power button again. When the marker is turned "on", the saved settings are
used. To turn off the marker, (Instant On - off) depress and hold the power button for 2
sec, (Instant On - on) switch off.
Note1: When you first connect power to your T-board, it will power up immediately and Disco the LED to load the default settings..
Use the Membrane pad to turn off. Everytime after that the T-board will function as you set it up to.
Note2: DIP switch 1 is the Tournament lock. Turn ON for tournament settings.
Shot Q’ing - If enabled, when the
trigger is pulled and no ball is in the breech, the marker will wait up to .25 sec for a ball to enter the
breech and will AUTOMATICALLY fire.
This feature prevents "lost" shots because your fingers are faster
than your hopper, and is still legal on most fields since it does not add shots.
ABS (Anti-Bolt Stick) - If enabled, the first shot will have the ABS dwell
(dwell + ABS setting). All other shots will have the standard dwell. If the marker is not fired for 10 sec, the first
shot will have the ABS setting again.
Force Semi Mode - If the trigger is
pulled and held long enough (Force Semi Time), the marker is
automatically set to semi mode, the eyes disabled, and ROF set to 13bps. This is to
guarantee the marker will function, regardless of the eye or mode.
Note: This feature is disabled on any mode that requires you to
hold the trigger. (NXL, Nitro, Auto)
To disable/enable the eyes - push the
eye button (membrane pad) or setup button on the board until the LED turns RED (disabled, ROF
capped), BLUE (disabled, ROF uncapped) or GREEN (enabled).
When the eyes are disabled, the marker is capped at 13bps, regardless of
MROF setting.
Changing Modes of Fire
1. Turn OFF marker. Hold down trigger and turn marker ON.
The LED will cycle through its colors very quickly (Disco), let go of
the trigger after the LED cycle. You are now in the Modes Menu.
2. Simply press the trigger to cycle through the modes. The color of the
LED indicated which mode you are in...
-Red - NPPL Semi
-Green - Reactive Trigger
-Blue - 3 Round Burst
-White - Full Auto
-Red - CFOA (capped semi)
-Purple - Nitro
-Yellow - PSP Ramping
-Teal - NXL Auto
3. Once you have selected the mode you want, tap the ON
button on the membrane pad (or pull and hold the trigger if not using the membrane pad),
the LEDs will cycle again to indicate that your setting has been saved.
4. The marker has returned to Live Mode with your desired mode of fire.
Adjusting Setting
With your ION T-Board, you have full control over how
your marker shoots. Below are the instructions for changing your settings.
This may sound confusing at first, please read the sample below the
chart.
1. Turn Off marker
2.Press and HOLD the EYE button (Setup button if you don't have a membrane pad).
3. While holding the EYE button, tap the POWER button
4. Continue to hold the EYE button, the LED will flash red once, pause, then
flash once again. At this time you can let go of the EYE button and you are
now in Setup1 (Reference Chart Below). IF you continue to hold the EYE
button after the first LED blink, and the second LED blink, it will then
blink twice together. If you let go, this will bypass Setup1 and bring you
straight to Setup 2. If you hold the EYE button until the LED blinks 3 times
together and release the EYE button, this will restore the default
settings.
5. Once you are in your desired Setup Menu, the LED color will indicate
which setting you are currently in. Pull the trigger X amount of times to
set your setting. The first pull of the trigger sets the value at its
minimum, each pull after that increments the value based on the chart
below.
6. Tap the EYE button to move on to the next setting. You can also ignore a
setting and bypass to the next setting by not pulling the trigger, and just
tap the EYE button till the LED indicates the setting you desire.
7. When finished with your settings, you can tap the POWER button to enter
Live mode, from any setting or Setup Menu. If you cycle through all the
settings, the marker will automatically exit the menu, and enter live
mode.
8. The LEDs will cycle quickly to indicate your settings were saved.
|
Setup 1 |
Default |
Min(ON) |
Max(OFF) |
Incrmnts |
Color |
|
ROF |
15 |
9 |
50 |
1 bps |
Red |
|
Dwell(SON) |
5ms |
2 |
256 |
.5ms |
Green |
|
Debounce |
5ms |
0 |
256 |
1ms |
Blue |
|
Classic/Automatic |
Auto |
Auto |
Classic |
toggle |
White |
|
Force Classic |
2 sec |
0.5 |
none |
.5 sec |
Teal |
|
Setup 2 |
|
|
|
|
|
|
Shot Q’ing |
ON |
ON |
OFF |
toggle |
Yellow |
|
After Nitro |
Semi |
n/a |
n/a |
cycle |
Purple |
|
Trigger speed |
5bps |
5bps |
None |
1bps |
Green |
|
Trig pulls to ramp |
4 pulls |
2 pulls |
256 |
1 pull |
Blue |
|
Setup 3 |
|
|
|
|
|
|
CDEL |
6ms |
1ms |
265 |
1ms |
White |
|
CON |
60 |
25 |
256 |
1ms |
Teal |
|
CTO |
250 |
0 |
256 |
10ms |
Yellow |
|
Eye Delay |
10 |
0 |
256 |
1ms |
Blue |
|
COFF |
10 |
0 |
256 |
1ms |
Purple |
|
Eye Type |
Bounce |
Bounce |
Break |
toggle |
Red |
|
Training |
OFF |
OFF |
ON |
toggle |
Green |
|
Setup 4 |
|
|
|
|
|
|
Restore Default |
n/a |
n/a |
n/a |
n/a |
n/a |
|
Setup 5 |
|
|
|
|
|
|
Eye Alignment |
n/a |
n/a |
n/a |
n/a |
Red |
Setup1
ROF - Firing speed of the marker
- Min. 9bps -
Dwell - Time the firing Solenoid is on -
Min. 0ms - Increments 1ms
Debounce - Debounce of trigger -
Min. 2ms - Increments 1ms
Auto/Classic - Auto mode uses the eye to close the bolt
- Classic closes the bolt when you release the trigger.
Force Classic - Time needed to force
marker into classic mode. this guarentees your maker will function if your eye fail.
- Min. Disabled - Increments 0.5 sec.
Setup2
Shot Q’ing - If the trigger is
pulled and no ball is in the breach, the marker will wait for up to ¼
sec for a ball to enter the breach and then will AUTOMATICALLY fire.
After Nitro - The LED will blink
Purple followed by the color of the switched mode. Pull the trigger to
cycle the modes.
ABS - On first trigger pull, ABS
is disabled, after that, each trigger pull will increment the ABS 1ms
Trigger Speed - Minumum Trigger
pull speed to activate ramping. I.E. 5bps
Trig pulls to ramp - number of
trigger pulls needed to start ramping.
Setup3
CDEL - Cocking Solenoid Delay Time: After the
hammer has been released, time is needed to allow the hammer to open the valve, and for the ball to leave the barrel completely
before the bolt opens. That is the CDEL. If the CDEL is too short, blow back up the feed tube is the result, if it is too long, it needlessly
slows down the cycle of the gun..
CON - Cocking Solenoid On Time. This setting determines
how long the cocking solenoid will channel air to the front of the ram, to open the breach. If the CON time is too low, the
gun not recock. If its too long, you will lower your max ROF. It should only be high enough to recock the marker everytime.
CTO - Cocking Solenoid Time Out. This setting is the longest
delay that the bolt will stay open when the eye is turned on. If the eye detects a ball in the feed tube, it will close immediately. If the eye
does not detect a ball, then the bolt will stay open till the CTO ends..
Eye Delay - Delay to allow the ball to drop completely into the chamber before the bolt closes.
COFF - Cocking Solenoid Off Time. This setting controls the minimum
amount of time the cocking solenoid directs air to the back of the ram, to close the breach. If the COFF time is too low, the bolt won't close
completely after each shot. This can cause shoot down when the gun is firing quickly because the air port in the bolt will not be aligned with
the air port in the body, causing a drop in velocity. Worst case, this can cause balls to break in the barrel, because they are smashing into each other.
Eye Type - Bouncebeam or Breakbeam eye type avail.
Training - Marker will function normally, but will not fire.
Setup4 - restores
default factory settings
Eye Alignment Tool
When in the Eye Alignment Tool, the LED will light up when the eye is
properly aligned. If the eye is blocked or misaligned, the LED will NOT
light. this tool is used to verify that your eyes are clean and
functioning.
|
